Polymers

POLYETHYLENE

Haldia Petrochemicals Limited is the second largest manufacturer of polyethylene in India with a total capacity of over 7, 00,000 tonnes per annum. It caters to more than 70% of the demand in eastern India and 15% on overall country basis. The product portfolio under polyethylene segment consists of various grades of High Density Polyethylene (HDPE) and Linear Low Density Polyethylene (LLDPE).

HPL manufactures a wide range of HDPE grades having narrow, medium & broad (bi-modal) molecular weight distribution using Mitsui Slurry CX Process to suit a wide range of end uses

HPL also manufacturers various grades of LLDPE in the swing LLDPE plant using Spherilene Gas Phase Swing Process from Basell, Netherlands. The LLDPE plant is the 3rd such plant worldwide using above technology and is used for manufacturing of various HDPE grades too.

These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, automobiles, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to more than 20 countries in the world.

Technology Partner – Mitsui, Japan

End Uses: Woven sacks; raschel bags for fruits & vegetables; containers for packaging edible oil, processed food, FMCG, lubricants, detergents, chemicals, pesticides; industrial crates & containers; carrier bags; houseware; ropes & twines; pipes for water supply, irrigation; process industry & telecom.

Major grades under HDPE are

Category Grade MFI Density Major Applications Datasheet MSDS
Film F5400 0.09 0.954 General purpose film, Thin reinforced carry bags F5400.pdf HD.pdf
HD T6 0.50 0.961 Lamination films, woven sacks and tarpaulin HD T6.pdf
Raffia R5801 0.50 0.961 Stretched tape/raffia for woven sacks and tarpaulin R5801.pdf
Y5401 0.80 0.954 Stretch Tape / Raffia / Yarn for Woven Sacks and Tarpaulin Y5401.pdf
Blow Molding B5500 0.35(I5) 0.956 Medium to large bulk containers for chemicals, detergents or lube oil B5500.pdf
B6401 0.40 0.964 Containers for lubricants and edible oil (up to 20 L) B6401.pdf
E5201 0.35 0.952 High ESCR blow-molding, cable sheathing and jacketing, lamination and general purpose film, extrusion applications E5201.pdf
E5201S 0.35 0.958 General purpose blow-molding applications E5201S.pdf
Pipe P5300 0.25(I5) 0.948 High pressure pipe applications P5300.pdf
P5200 0.80(I5) 0.948 Pipes (PE 63) - Pressure pipes for Drinking Water, Irrigation P5200.pdf
P5200UV 0.80(I5) 0.948 Telecom ducts, Pressure pipes (PE 63) for Drinking Water, Irrigation – UV Stabilised P5200UV.pdf
P5100 0.50(I5) 0.948 PE 80 compliant pressure pipes P5100.pdf
Injection Molding M5818 19.0 0.956 General purpose injection molding M5818.pdf

Category Grade MFI Density Major Applications Datasheet MSDS
Monofilament HD T10 1.1 0.950 Monofilament for net, twines and ropes HD T10.pdf HD.pdf
HD T10S 1.1 0.950 Monofilament for net, twines and ropes HD T10S.pdf
Raffia HD T9 1.1 0.950 Stretched tape/raffia for woven sacks and tarpaulin HD T9.pdf
Film F5001 1.1 0.950 Blending resin in HDPE packaging film F5001.pdf
Blow Molding B6001L 0.5 0.960 Blow molded containers (up to 20L)for edible oil, lubricants B6001L.pdf
Pipe P4600L 1.1(I5) 0.946 Pipes (PE 63) - Pressure pipes for Drinking Water, Irrigation P4600L.pdf
Injection Molding M5002L 2.5 0.950 Molded caps & closure application M5002L.pdf
M5005L 4.5 0.950 Injection molding of heavy duty crates and industrial products M5005L.pdf
M6007L 7.5 0.950 Injection molding of heavy duty crates and industrial products M6007L.pdf
M6007LU 7.5 0.950 Injection molding of heavy duty crates and industrial products with UV Stabilization M6007LU.pdf
M5018L 19.0 0.950 General purpose injection molded applications M5018L.pdf
M5025L 30.0 0.950 General purpose injection molded applications M5025L.pdf

Technology Partner – Spherilene , Basell

End Uses: General purpose packaging film, Rotomolded tanks, Drip lateral, Extrusion-coating of woven fabrics and low voltage power cables. Major grades under LLDPE are

Category Grade MFI Density Major Applications Datasheet MSDS
Film
71501S 1.0 0.920 General purpose packaging film 71501S.pdf LLDPE_MSDS.pdf
71601W 1.0 0.916 General purpose adhesive lamination film 71601W.pdf
71602S 2.0 0.920 General purpose packaging film 71602S.pdf
71602W 2.5 0.916 General purpose packaging film 71602W.pdf
92001S 1.0 0.920 Hexene-1 LLDPE copolymer for Mono and multilayer Packaging Films 92001S.pdf
92001W 1.0 0.920 Hexene-1 LLDPE copolymer for Adhesive Lamination Films 92001W.pdf
Drip Lateral 71601D 1.0 0.920 Drip laterals 71601D.pdf
Extrusion Coating 72307E 7.0 0.926 Extrusion coating of HDPE woven fabric, aluminum foil, jute, paper and allied substrates 72307E.pdf
Rotomolding 73005T 5.0 0.934 Tanks and container for domestic or industrial water storage, sanitation, agriculture 73005T.pdf
73005TU 5.0 0.934 UV stabilized tanks and container for domestic or industrial water storage, sanitation, agriculture 73005TU.pdf
73204T 5.0 0.932 Tanks and container for domestic or industrial water storage, sanitation, agriculture 73204T.pdf
73204TU 5.0 0.932 UV stabilized tanks and container for domestic or industrial water storage, sanitation, agriculture 73204TU.pdf
Wire & Cable LL T12 3.7 0.926 Low voltage power cable insulation LL T12.pdf

Polypropylene

HPL manufactures 3,41,000 tonnes polypropylene per annum using Spheripol-II technology supplied by Basell, Netherlands. Spheripol process is the most widely accepted technology for manufacturing Homopolymers and Copolymer grades. The unique process capabilities and high consistency in product morphology ensure excellent quality.

These products from HPL are of benchmark quality, meeting the highest international standards and are used extensively by packaging, consumer durables, houseware, furniture, container or luggage manufacturers in India and abroad. Due to superior quality, HPL products are in demand in various countries from EU, South East Asia, USA etc. HPL products are exported to several countries in the world.

Major Brands, Grades End Uses

Technology Partner –-Basell, Netherlands

End Uses: Woven sacks for cement, foodgrains, sugar, fertilizers; leno bags for fruits vegetables; TQ BOPP films and containers for packaging textiles, processed food, FMCG; office stationary; components for automobile and consumer durables; molded furniture & luggage; houseware; geotextiles; fibers for socks, sports wear; soft luggage.

Major grades under Polypropylene are

Category Grade MFI Density Major Applications Datasheet MSDS
Homopolymer - Extrusion F103 3.3 0.90 BOPP Film Grade - General Purpose, Lamination & Metallizable films F103.pdf PP.pdf
F135 35 0.90 Nonwoven Fabric, Multifilament Yarns, Extrusion Coating F135.pdf
R103 3.3 0.90 Raffia Tapes ,Woven Sacks for Packaging Fertilizers, Cement, Polymers, Carpet Backing ,FIBC etc. R103.pdf
T103 3.3 0.90 Thermoformed Cups, Containers & Other disposable items T103.pdf
T105N 35 0.90 Thermoforming Cups, Containers & Other disposable items T105N.pdf
F110 11.0 0.90 TQ and Cast Films for General Purpose Packaging etc. F110.pdf
Homopolymer – Injection Molding M103 3.0 0.90 General Purpose Injection Molding M103.pdf
M106 6.0 0.90 General Purpose Injection Molding M106.pdf
M108 8.0 0.90 General Purpose Injection Molding M108.pdf
M110 10.0 0.90 General Purpose Injection Molding, Furniture etc. M110.pdf
Impact Copolymer – Injection Molding M304 3.5 0.90 Automotive Components, Crates, Pails, Furniture etc. M304.pdf
M307 7.0 0.90 General Purpose Injection Molding M307.pdf
M310 10.0 0.90 Battery Boxes M310.pdf
M311T 10.0 0.90 Compounding, Automotive Components, Luggage and Industrial Components M311T.pdf
M312 12.0 0.90 Compounding, Industrial Components, Automotive Components, Luggage, Pails, Houseware, Sanitary Wares etc. M312.pdf
M315 15.0 0.90 General Purpose Injection Molding M315.pdf
M325 25.0 0.90 Compounding, Automotive Components, Houseware, Appliances parts, Extrusion Coating M325.pdf
M340 40.0 0.90 Appliance & White Goods, Automotive component, Compounding,TWIM M340.pdf
M365 65.0 0.90 Compounding, Automotive components, Appliances & TWIM M365.pdf
Random Copolymer – Blow Molding B202S 1.9 0.90 Bottle & Containers for Medical and Transparent Products (e.g. IV Fluid Bottles) etc B202S.pdf
B200 1.9 0.90 General Purpose Blow Molded & Thermoformed Items, Sheets for Files & Folders. B200.pdf
Random Copolymer – Injection Molding M212S 12 0.90 High Clarity Containers, Household items,Injection Syringe, Laboratory products & ISBM Bottles M212S.pdf